0 Setting Router Cisco [Part I]

Lihat Gambar Jaringan di bawah ini
Bagaimana konfigurasi Router Cisco untuk desain jaringan tersebut??

KALO MAU LEBIH JELAS KLIK PADA GAMBAR


Berikut adalah konfigurasi Router nya:

1.)  Konfigurasi Router 0

Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.

//SETTING INTERFACE FASTETHERNET 0/0
Router(config)#int f0/0
Router(config-if)#ip address 172.16.10.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

//SETTING DHCP
Router(config-if)#ip dhcp pool dhcp1
Router(dhcp-config)#network 172.16.10.0 255.255.255.0
Router(dhcp-config)#default-router 172.16.10.1
Router(dhcp-config)#ex

//SETTING INTERFACE SERIOAL 0/0/0
Router(config)#int s0/0/0
Router(config-if)#ip address 8.8.8.8 255.255.255.0
Router(config-if)#clock rate 1200
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down
Router(config-if)#ex
Router(config)#ex

//SETTING ROUTING
Router(config)#router rip
Router(config-router)#version 2
Router(config-router)#network 8.0.0.0
Router(config-router)#network 172.16.0.0
Router(config-router)#network 192.168.10.0
Router(config-router)#network 202.10.10.0
Router(config-router)#network 192.168.0.0
Router(config-router)#ex
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console

//SIMPAN KONFIGURASI
Router#wr
Building configuration...
[OK]

2.) Konfifurasi Router 1
Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.

//SETTING INTERFACE SERIAL 0/1/0
Router(config)#int s0/1/0
Router(config-if)#ip address 8.8.8.9 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial0/1/0, changed state to up

Router(config-if)#ex

//SETTING INTERFACE FASTETHERNET 0/1
Router(config)#int f0/1
Router(config-if)#ip address 192.168.10.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

//SETTING DHCP FASTETHERNET 0/1
Router(config-if)#ip dhcp pool dhcp2
Router(dhcp-config)#network 192.168.10.0 255.255.255.0
Router(dhcp-config)#default-router 192.168.10.1
Router(dhcp-config)#ex

//SETTING INTERFACE FASTETHERNET F0/0
Router(config)#int f0/0
Router(config-if)#ip address 202.10.10.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

//SETTING DHCP FASTETHERNET F0/0
Router(config-if)#ip dhcp pool dhcp3
Router(dhcp-config)#network 202.10.10.0 255.255.255.0
Router(dhcp-config)#default-router 202.10.10.1
Router(dhcp-config)#ex


//SETTING ROUTING
Router(config)#router rip
Router(config-router)#version 2
Router(config-router)#network 8.0.0.0
Router(config-router)#network 192.168.10.0
Router(config-router)#network 172.16.0.0
Router(config-router)#network 202.10.10.0
Router(config-router)#ex
Router(config)#
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console

//SIMPAN KONFIGURASI
Router#wr
Building configuration...
[OK]

Salam,,,,, Mr.Zer0